Engineer Recertification Practice Exam

These questions are part of the practice quiz. Start practicing

• How many tracks are located in the North yard in Harrison Yard?
• What is the first step in the procedure to charge a PA5 train?
• What is the maximum allowable speed in ATC Bypass mode?
• What is the purpose of operating the TOD selector during a malfunction?
• What action should be taken when the train is approaching a work zone?
• What is the specified location for the shunt indicator?
• What does the "Emergency pipe" refer to in the PA5 system?
• What happens when the emergency alarm is activated?
• What does the CBTC-TOD stand for in the context of train operations?
• Which tasks are critical to be performed before removing bus jumpers?
• What does the activation of the Door Interlock Bypass button require?
• In the event of a slow speed order, what should the engineer look for?
• What should the train engineer do if there is an improper short station stop in MCS mode?
• What is the pit speed limit at the Harrison Car Maintenance Facility?
• What action should be taken when operating in MCS mode with work zone indication?
• Which of the following is NOT a piece of safety equipment for engineers?
• What does the triangle alongside the MAL bar indicate?
• What is the primary purpose of a safety vest for engineers?
• What communication system is used by PA5 train crews?
• What is the proper way to reset the emergency stop push button on PA5 cars?
• What is the final step in uncoupling procedures for PA4 cars after all actions are completed?
• How can a train engineer ensure compliance with speed restrictions in Release mode?
• What is the maximum allowable speed in other tracks in Harrison Yard according to Rule 102?
• What happens if the ATC system fails while approaching a signal?
• What is the role of the handbrake when working on a car?
• What is the minimum requirement for safely initiating train movement in MATC mode?
• How does a train engineer respond to a Train Hold indication?
• Where is the brake cut-out lever located on PA4 cars?
• What is required to be done with the ATC Start button during MATC operations?
• What is the result of activating the emergency brake valve incorrectly?
• What indicates a CBTC emergency brake application?
• How should a train respond to a signal indicating it can pass?
• What happens when the control cut-out circuit breaker is in the 'OFF' position?
• What should be done in response to a CBTC TOD failure while the train is in motion?
• What is the Trip ID code for the route from JSQ to 33rd?
• If carborne ATC equipment fails, how must the train be operated?
• What action must the engineer take when a Station Restriction MAL is present?
• Which route is identified in the MATC operating context?
• What is the first step in the process for removing bus jumpers?
• If you overrun a station by half a car in ATC Bypass mode, what should you do?
• Which of the following is part of the safety protocol before using equipment?
• What must occur before starting train movement in MATC mode?
• Where is the manual cutting lever found?
• What must the train engineer do in MATC mode when making an employee pick-up?
• What does a white strobe indicate in the track area?
• What does Rule 102 state about speed limits on tracks entering shop buildings in Harrison Yard?
• What should the engineer do if doors need to be reopened after being closed and locked?
• What is the correct action when stopping a train upon flagging?
• What is necessary after activating the Door Interlock Bypass to put a car into motion?
• When should a Class II brake test be performed?
• What should the engineer be prepared to do if the good section has fewer cars when splitting the train?
• What is the pilot's responsibility regarding interlocking signals?
• What is the significance of one long whistle from the tower?
• What should be done before removing a wall (auxiliary) trolley from a car?
• What is essential for operating the ATC Bypass mode properly?
• Where is the high voltage breaker located on a PA5 car?
• Which Trip ID code corresponds to the journey from Hoboken to World Trade Center?
• What is a requirement when employees are in track area according to safety protocols?
• What action must the train engineer take when acknowledging a transition in mode on the system?
• What does an active PA-5 cab display show on the TOD screen?
• What is the brake pipe pressure when fully charged on a PA4 train?
• What is the best strategy for operating in MCS mode?
• What position should the ATC mode switch be in for territory transition?
• How many handbrakes are required when laying up a train at signal R8X in Newark?
• What operation mode is indicated when a train is in emergency braking due to flagging?
• In the context of train operation, what does "CBTC Available" indication signify?
• What does 'CBTC Available' indicate?
• What action is required when carrying out a daily test?
• What should a train engineer do if they encounter a malfunctioning emergency brake?
• What action must a train engineer take if an improper short stop occurs in MATC mode?
• Who provides the direction for operating the ATC Bypass Switch?
• Is MATC mode permitted during employee pick up?
• What is the hand signal for 'Stop'?
• What does the observed speed icon indicate on the speed dial?
• Is a mode change necessary in MATC mode when approaching a work zone?
• What limits the speed of a train operating in Release mode?
• What is the recommended action when operating a train under low adhesion conditions?
• In what position must the drum switches be at both operating ends of a PA5 train ready for passenger service?
• What does the ADCL light indicate on PA5 cars?
• What is essential to avoid when crossing over the third rail?
• What is the procedure following a successful coupling?
• What indicates that the ATC system has detected a fault?
• When laying up a train at signal R8X, what is required?
• What is the effect of the drum switch in the "Advance" position on the rear of the train?
• What is the proper whistle signal to release brakes, proceed, and acknowledge signals?
• What should be done first when loss of motor power occurs on the PA4 train?
• What is the proper procedure for entering a shop building with a car?
• Who should you contact if you are late for your job?
• What does the Minimum Allowable Level (MAL) indicate when approaching a failed signal?
• What do trains proceed on in Release mode?
• When is the mode change boundary for movement into Yard territory reached?
• What automatic action occurs when a train exceeds 12 mph in Release mode?
• What does daily test verification assess in carborne ATC equipment?
• What does the Zone Controller verify regarding the train?
• What does the MAL bar with green and yellow sections signify?
• Which of the following keys is NOT required to operate the PA-5?
• Where are side inclines located on a train?
• What is indicated by the 'Doors to Open' signal?
• What is the proper way to resume normal speed when encountering a green flag?
• When should the Door Enabler be activated in Bypass mode?
• What should the train do after receiving permission to pass a signal?
• Which tracks are found in the West yard in Harrison Yard?
• What should be done if the ATC Bypass Switch seal is broken?
• What designation is used for trains that are Not in passenger service?
• Who operates the doors in the MATC system?
• What does Rule 101 permission entail?
• What is the correct whistle signal for running against traffic?
• What signifies a main reservoir rupture on a PA5 train?
• What indication appears when a train is correctly positioned at a station stop in MCS or MATC modes?
• What indicates that a train is approaching with flashing green signals?
• Which interlocking signals are used in Harrison Yard for permissive signaling?
• What is the effect of failing to stop for an employee pick-up?
• What does a track indicator specifically help engineers determine?
• What signifies the speed limit from the car-borne map for ATC systems?
• How does the operation of trains differ between CBTC and non-CBTC yard territory?
• What should be done in response to a TOD and wayside signal indication?
• What is the significance of the parking brake gauge being in the yellow zone?
• What action should a train engineer take if the train loses air while approaching a station?
• What is indicated by the "Hold" symbol on the TOD?
• What happens if the MR pressure drops below 95 psi?
• What condition is indicated by a Low Adhesion display on the TOD?
• What does the track area walking restriction indicate for employees?
• What condition must be met before operating in Release mode?
• What rule governs the procedure to pass an automatic signal at stop?
• Where are the low-voltage circuit breakers located on PA5?
• What does a flashing green signal imply while approaching a station?
• When resetting motors on a PA4 train, which key action should be performed?
• What is the acceptable route for high or wide loads through Journal Square?
• Which type of key is required for operating the PA-5?
• What is the first step in the procedure for uncoupling PA4 cars with the cab at the point of the cut?
• What action causes the brakes to activate in an emergency?
• What should an operator do when On-Track Safety flagging is posted without work zone indication?
• What should train operators verify when encountering yellow flags in MATC mode?
• How many tracks in Harrison Yard are equipped with derailers?
• What is the maximum speed allowed through 1 Track in Harrison Yard?
• How should orders be confirmed to ensure effectiveness?
• What scenario would trigger an emergency brake application in ATC systems?
• What is the proper whistle signal to acknowledge a signal to back up?
• What is the first step when passing an automatic signal displaying 'Z' or 'D'?
• What is the maximum allowable speed for restricted speed?
• What is the speed restriction for trains operating in Release mode?
• What is crucial to ensure before departing a station with passengers?
• What component is essential for connecting a train to another train or car?
• What must the train engineer do to acknowledge a mode change on the TOD?
• What should an engineer do if an incorrect Trip ID is detected?
• What is the correct reaction when a PA5 emergency stop button is reset?
• What should always be done when using the hand trolley?
• What are the positions of the ATC mode switch on PATH?
• What happens to a train with the ATC mode switch in the Release position at a territory boundary?
• What does the signal aspect refer to?
• Why does carborne ATC request the train engineer to reconfirm the train length?
• Where can gamewell/emergency alarm boxes be found?
• What must be ensured during a breakdown recovery operation?
• What must be done to enable doors that have been closed during a restriction?
• What happens to the signal under CBTC when there is a failure?
• How far in advance does the TOD indicate an approaching work zone?
• What is the maximum speed allowed in tunnels E and F under STDS?
• What happens if the reverse switch is not set correctly when using the Emergency Pipe?
• What is the maximum allowable speed for a train in Bypass mode?
• How many cars on a PA5 train are equipped with air compressors?
• What does the TOD indicate during train operations?
• Where is the ATC Bypass Switch located?
• What is the normal pressure range for the main reservoir on PA4 and PA5 cars?
• What are the positions of the ATC mode switch?
• After requesting permission to pass a stopped automatic signal, what must the engineer do?
• For ATC systems, what happens when a train follows a non-ATC train?
• What is a necessary item for flat crew operations?
• What signal is used for calling for a signal?
• What is the braking action required if brake pipe pressure drops below acceptable levels during a straight air rupture?
• When is it acceptable to operate a train without following posted flagging?
• What does the yellow zone indicate on the PA5 parking brake reset gauge?
• What position should the coupler control lever be in between a PA-4 work car and a flat?
• What is the pit speed limit at running repair?
• What is indicated by the key on "W"?
• During the MATC mode, how often must the ATC Start button be activated?
• What should one do if they approach an area marked by a blue flag?
• How must the Alerter be used under ATC?
• What mode must be enabled for the train to pass the call-on signal aspect?
• Which tunnels operate against traffic from Grove St to Hoboken?
• What action should be taken when adding to a trouble train with an electrical problem?
• What is the required speed reduction when observing one yellow flag?
• What does a sign marked 'W' indicate?
• What does dwell time represent?
• What must employees in the track area be alert for?
• What action should be taken if the Train Order Device (TOD) fails?
• What action should you take if you disagree with the Low Adhesion condition displayed?
• What is the proper buzzer signal for standing to back up?
• What is the yard speed restriction according to Rule 102?
• How does the Emergency Pipe on the PA5 function?
• What feature is typically installed in a CBTC Yard?
• What does a safety flashlight serve as in safety equipment?
• During the localization process of an ATC-equipped train, whose confirmation is necessary regarding train length?
• Why is there a specific waiting time after a CBTC failure with emergency brake application?
• What is the role of live contact shoes on a car?
• Which controller positions are found on the PA5 system?
• What does a solid blue light on the exterior of a PA5 car indicate?
• What does a flashing red light over the letter 'O' indicate?
• Where can you find the emergency pry/crow bar on PA5 cars?
• In an emergency response protocol, what is the priority for the train engineer?
• What operating mode should a train switch to after an ATC failure in CBTC territory?
• What mode is indicated by the term "MCS" in train hold removal?
• What information does a track indicator provide?
• What is the location of the Washington Street emergency exit?
• Which situation is NOT a valid reason for using Release mode?
• How is the length of the train determined during the localization process?
• What speed must be maintained during initial movement in ATC Bypass mode?
• What is the maximum pressure range for the PA4 brake cylinder?
• What happens to the train's speed when it exceeds the threshold in Release mode?
• What does the disappearance of the Out of Service indication signify?
• What does the green MAL bar indicate?
• What is the effect of the ATC Door Mode switch in the Cut-Out position?
• What mode indicates operating with work zone indication?
• When using Motorman's Bypass, what should the cab be used for?
• What should be done if a Train Hold is in effect?
• What must be done if a train experiences a loss of stationing numbers?
• What should be done if a train approaches a blue flag?
• What should be done immediately after a daily test failure?
• What should be the immediate response to an ATC failure indication?
• Which factor contributes to the safe operation of the ATC system?
• What should the train conductor do if the TOD indicates a malfunction?
• What is the primary purpose of a station restriction?
• What is indicated on the CBTC-TOD for employee pick-up?
• What action should be taken if Stop and Stay cannot be released?
• Before energizing the overhead trolley, what should you verify?
• What indicates the loss of MAL during train operation?
• What should you do if damage is found during the inspection of bus jumpers?
• How should the brakes be applied if the master controller cannot be moved to the OFF position?
• When does the ATC system request train length confirmation?
• When approaching a flashing red order signal, what indication is provided on the CBTC-TOD?
• Are there restrictions on ATC operations in Yard territory?
• What indicates that third rail power has been removed on PA4 cars?
• What is the main function of the master controller in PA4 cars?
• Where are the permissive signals located?
• What situation may lead to an emergency brake application while in Release mode?
• What signifies optimal train movement for service?
• How does the engineer ensure compliance during ATC Bypass mode?
• What mode does the train engineer operate under in a situation with an Order Signal under ATC?
• Where would one typically find the control cut-out circuit breaker in a PA4 car?
• What must a train do before transitioning into Release mode?
• Who is responsible for complying with speed restrictions in yard mode operation?
• What does a blue flag indicate?
• What is the primary role of data read from wayside transponders for ATC-equipped trains?
• What should be done first if smoke is observed in the tunnel while operating a PA5 train?
• What is a principal indication of a Brake Pipe rupture on a PA-4 train?
• What should be done if a Slow Speed Order is issued during transit?
• Do flashing green signals appear when the ATC Bypass is engaged?
• During an emergency stop, what is a critical action besides applying brakes?
• In what mode is the train allowed to bypass certain speed controls?
• What happens if a train transitions into Release mode while in motion?
• What is the first correct step if a Brake Pipe rupture occurs?
• What is the result of the Stop and Stay function when entering or leaving the station?
• What occurs when a train stops due to an emergency brake application?
• What does a green MAL bar represent?
• What should be done when encountering yellow flags without work zone indication?
• If a train loses its air while entering a station in Bypass, what should be done?
• When should a conductor signal for a brake application during a CBTC system failure?
• What must occur to return to normal operation after accepting a call-on?
• What is the acceptable position of the ATC mode switch when leaving the cab?
• What indicates a successful emergency braking action on PA5 cars?
• What does the car-borne ATC assessment of train data allow for during operations?
• What is the maximum distance indicated by the green MAL bar?
• In which mode does the train operate within the Yard under the train engineer's control?
• What is the first step in the procedure for coupling with a cab at the point of the add?
• What is the status of the 17 track in Harrison Yard?
• What occurs when a train enters Yard territory with the ATC mode switch in MATC position?
• What should the brake pipe pressure be maintained above to ensure sufficient braking power?
• What must be applied to ensure safety when working on a car?
• What items must be checked before moving car(s) from a shop track?
• What is the consequence of ignoring a Call for Orders signal?
• What is a key step when determining if a segment of a split train takes power?
• What is the correct action if the seal on the ATC Bypass switch is missing?
• What does a station dwell time reading in green signify?
• What does the indication of a clear track mean for train operations?
• What is the maximum speed through an interlocking as defined in rule 279?
• What is the correct whistle signal to apply brakes or stop?
• When is the ATC start button required to be pressed during MATC operations?
• What does three long buzzers from the conductor indicate?
• When should power be restored after installing bus jumpers?
• What is the correct position for the MC handle when activating the Door Interlock Bypass button?
• What is the maximum operational speed for a train in Release mode according to regulations?
• What allows for the effective communication between ATC systems on trains?
• What is the function of the green signal in ATC operations?
• Under what conditions will a Trip ID be absent?
• What is the main risk associated with the dynamic brake system in PA4?
• What position should the ATC Bypass switch be in when leaving the cab?
• What actions should be taken regarding a blue flag?
• What is the required action in the yellow zone on the speed dial?
• Is it permissible to select Release mode authority?
• What should be done when a Slow Speed Order is indicated on the TOD?
• What happens to train operation during ATC Bypass mode?
• When should the vapor key be removed from the coupler key switch?
• Can Slow Speed Orders be traversed in MATC mode?
• What is required for a train to resume normal operations after exiting Release mode?
• What is the normal range of Emergency Pipe pressure in FS brake on PA5 cars?
• Which operation speed limit is enforced by ATC in yard mode?
• What is the status of employee pick-up while in MATC mode?
• What must be done after removing the cutting key during the uncoupling process?
• Which operational guideline must be followed every time a train stops?
• When will the Out of Service indication appear?
• What is the proper whistle signal for approaching workmen?
• What should be done if there is a straight air rupture on a PA4 train?
• What is the Brake Pipe pressure on PA4 cars when brakes are fully released?
• What does a solid yellow light on the exterior of a PA5 car indicate?
• When operating in release mode, what is the expected behavior when encountering a signal that requires stopping?
• Which of the following actions should not be taken when handling a Call for Orders signal?
• What is the maximum speed limit in Yard mode according to ATC restrictions?
• What is one of the safety checks performed before releasing handbrakes?
• What should be ensured before moving or adding to a train or equipment with a blue flag present?
• What does the Stop and Stay function apply to the train?
• How many long sounds signify an airbrake test?
• When can a train leave a station according to the restrictions?
• How many maximum cars can be displayed on a PA5 TOD screen?
• What is the signal series in Tunnel A?
• What action is not recommended when an engineer encounters an incorrect Trip ID?
• What is the correct procedure when making a cut between two PA5 cars?
• What is the speed limit for train operation in Release mode?
• What type of signal do two yellow flags indicate?
• What should a train operator do when entering a different territory from CBTC mainline?
• In MATC mode, what does operating with work zone indication require?
• What is the maximum speed allowed through a station when not stopping?
• In an emergency, if air is lost in a train, where should the engineer prioritize communication?
• When is the Straight Air pressure expected to register between 45 and 60 pounds on a PA-4 train?
• What is the role of the ATC in relation to speed limits?
• In MATC mode, what must the Train Engineer do when approaching a Call for Orders location?
• What indicates an unknown operating mode condition?
• How can a train transition from Release mode into MCS mode?
• What is the main method for removing power from a train?
• What is the procedure for performing a Class 1A FRA air brake test?
• What is the procedure for a train in MCS approaching a work zone?
• How is train delocalization determined?
• From where can parking brakes be applied?
• What should you do if you find defects in a portable hand trolley during inspection?
• What does the ATC train's Maximum Allowable Speed (MAL) generally reflect?
• Under ATC, how is the use of the Alerter viewed?
• When is Release mode primarily used?
• What is the consequence of a complete failure of the ATC carborne equipment?
• What should an engineer do before going beneath equipment to ensure safety?
• What happens to the brakes reaction on PA4s if the electric brake is cut out?
• What is the purpose of train orders issued?
• How do trains and wayside computers communicate with each other?
• What must a train engineer do if there is a track circuit failure during operation?
• What does the ATC Bypass mode indicate regarding speed signal compliance?
• Under which circumstances can a train pass a signal?
• What action does a speed dial exclusion indicate?
• In what position is the ATC Mode switch normally set in yard territory?
• If you encounter a flashing green signal on a curve, what action should you take?
• What happens when the MATC mode selection takes place while in motion?
• What happens if a train or rolling equipment passes a blue flag?
• What is the consequence of pulling the service brake application if the flashing mode indication is not touched within the allotted time?
• How should the brake handle be positioned when braking appropriately after a loss of power?
• What is the responsibility of the engineer when a MAL bar indicates caution?
• Which of the following represents a full service function on PA4 brake valves?
• What should you check before using a wooden slipper?
• What precaution should be taken when an engineer goes beneath equipment?
• What circuit breakers are cut out if the PA4 train is bucking?
• What should an engineer check for in the operating cab two minutes before departure?
• What does the ADCL indication light signify in the PA5 engineer's cab?
• What is one purpose of the Low Adhesion function in train operations?
• Under which conditions does an engineer operate by absolute block?
• What indicates a Main Reservoir rupture on a PA4 train?
• What trip code is associated with Hoboken to 33rd?
• What signals access to CBTC Mainline territory?
• How does a train engineer change the operating mode from MATC to MCS?
• What is a potential indicator of a Straight Air rupture on a PA-4 train?
• In what scenario will a train not charge while in MATC mode?
• Which signal is symbolized by 'X'?
• What is not a condition for the absence of a Trip ID?
• What is a key indicator for transitioning from MATC mode?
• What required items must employees have to enter the track or tunnel area?
• When should an engineer be in the operating cab before departure?
• What does the ATC Door Mode switch in Cut-Out position signify?
• What must be followed when complying with Rule 231 signs in MCS mode?
• What is the Trip ID code for Newark to World Trade Center?
• What must the train engineer do if a Call for Orders signal is displayed?
• What identified condition will allow operation without a Trip ID?
• In what position should the angle valve be when closed on PA5 cars?
• What is the initial step to take if a PA4 train fails to take power?
• What is the required distance for indication of an approaching Slow Speed Order on a train?
• What does 'signal indication' refer to?
• What should be done if Brake Pipe pressure falls below 90 pounds?
• What occurs when an over-speed detection is triggered?
• What happens to the brake cylinder during the FRA Class II air brake test on PA5?
• When should high beams be displayed while operating PA5 cars?
• In Release mode, when can you expect to receive CBTC 'Proceed' signal aspects?
• What is required when operating the train in MATC mode with yellow flags/lamps?
• What should the train operator do in Release mode as per the Trainmaster's instructions?
• What should be used to track trains at Journal Square yards?
• In the event of an improper long station stop in MCS mode, what is the first step the engineer should take?
• Where is the location of the parking brake manual release handle on PA5 trains?
• Where is the air compressor switch located on PA4's?
• What are the positions of the master controller on PA4 cars?
• What action should be taken when hearing one long whistle from the tower?
• What is the primary function of the Low Adhesion feature?
• What is the Trip ID code associated with JSQ-33rd via Hoboken?
• What does the phrase "maximum power" refer to on a master controller?
• What is the signal series in Tunnel B going uptown?
• What role does the train crew play in MATC operations?
• What is the maximum number of cars that can fit on 7 track inside Harrison Yard?
• What is the initial step when closing up to a stalled train in a station under CBTC?
• Who is authorized to remove a blue flag?
• When encountering Rule 231 signs without a Slow Speed indication in MATC mode, what should be done?
• What is triggered when a flashing mode indication is not acknowledged in the allotted time?
• What is the method of passing electrical and communications signals from one car to another?
• What signal does 'Z/D' represent?
• Which of the following is true regarding the acceptable position of the ATC mode switch?
• What condition must be met before returning to normal operations after a call-on?
• What steps should be taken when laying up a train?
• What is the location of Caisson 2?
• What must a switchman ensure when placing a portable hand trolley to a car?
• Which mode would trigger an absence of Trip ID?
• Where are the TOD screens located on a PA5 'C' car?
• What is the initial step to transition into ATC Bypass mode?
• What happens when the train traverses a failed track circuit in release mode?
• Is MATC available in work zones?
• How is the action to be taken for Rule 231 signs defined in MATC mode?
• How can a train engineer resume operation in MATC after a stop?
• What is the proper procedure for performing a standing brake test?
• When should the engineer change back to CBTC MCS mode?
• What does ATC Bypass mode allow the train engineer to do?
• Where is the current operating mode displayed in the CBTC-TOD?
• What action should be taken to ensure the train is charged properly after installing bus jumpers?
• Which mode must be selected to depart from a station when the Train Hold is engaged?
• What should the engineer do upon receiving an over speed warning?
• Where is the control cut-out circuit breaker located on a PA4 car?
• Where is the motor control cut-out switch located in a PA4 car?
• What is the purpose of the running rail in train operations?
• When will a Station Overrun indication appear on the TOD?
• How many cars can fit on 5 Track west in Harrison Yard?
• What area comprises the Washington Street shaft?
• What should be done if the stop arm fails to clear?
• What identifies the #1 end of a C car on PA5s?
• When does an operating mode change occur while entering yard territory?
• What is the signal series in Tunnel E?
• What action should be taken if the Out of Service indication appears?
• Where is the motor reset button located in PA4 cars?
• Where is signal 788Z located?
• What feature of the system ensures that the ground controllers maintain awareness of train movements?
• Which of the following is NOT a position on the Brake Valve handle on PA4 cars?
• What is required for safely operating in CBTC mainline territory?
• What is the purpose of the Daily Test function of ATC car-borne equipment?
• What indicator signals that a train can proceed through a work zone?